Leading 10 usual forklift accidents ， forklift operation need to take note of these matters ！.

Do not undervalue the forklift at work. If the operation is bad, there will certainly be major accidents in minutes, and there are lots of mishaps including forklifts.

Instance 1: The forklift freight obstructed the motorist's view, and the individual ahead might not be discovered, causing a moving accident.
Case 2: In order to maintain the equilibrium of the forklift when lifting heavy products, the staff members used their body weight as the counterweight, which virtually created casualties.
Case 3: The width of the forklift cargo exceeds the allowed size of the route and holds on the roadside rack, which virtually triggers an mishap.
Situation 4: Forklift is speeding up and rolls over throughout a turn.
Situation 5: The forklift driver did not see the pedestrian, and the pedestrian did not see the forklift.
Case 6: The forklift lifts the workers unlawfully, the forklift driver does not use the safety belt, the forklift lifter drops and the driver is squashed when the forklift surrender.
Situation 7: The forklift motorist did not use a seat belt and dropped from the lorry when it surrendered and was squashed.
Forklift procedure should focus on these matters ：.

Begin.
1. Before starting, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn first and after that begin.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) gauge need to be secure before beginning.
3. When the forklift starts with a lots, the motorist should initially validate that the load is secure and reliable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the pole needs to be slanted backwards. .
2. Do not lift the fork too high when driving. When getting in and leaving the task site or while driving, be careful that there will certainly be no obstacles overhead. When the lots is traveling, the fork must not be increased expensive, which will certainly affect the security of the forklift. .
3. After dumping, the fork should be reduced to the regular driving placement before driving. .
4. When transforming, if there are pedestrians or vehicles close by, the driving signal should be released first. High-speed sharp turns are restricted. High-speed doglegs will trigger the automobile to lose side security and topple. .
5. When the forklift is downhill, it is strictly prohibited to turn off the fire and slide, and it is restricted to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it needs to obey the traffic rules in the factory and have to keep a specific security distance from the lorry in front. .
7. When the forklift is running, the load has to remain in the lowest setting that does not prevent the driving, and the gantry ought to be properly tilted back. The tons will not be increased other than when piling or loading. .
8. The height of the tons should not obstruct the chauffeur's sight. In special conditions, when the item affects the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to activate the ramp, neither to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it must drive securely at a reduced speed when entering the production workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for workers to stand on the fork to hold things and play a stabilizing function. .
12. If problems are found, they will be repaired and reported in a prompt way, and they will never ever run with diseases or conceal them.

loading and discharging.
1. When fork-loading items, the range between both forks need to be adjusted as required to make the tons of both forks balanced and not manipulated, and one side of the thing need to protest the rack. .
2. It is prohibited to work with a solitary fork or utilize a fork top or pull. In unique circumstances, safety and security warning signs need to be established to remind bordering pedestrians. .
3. In the process of packing and dumping items, the forklift has to be braked with the brake. .
4. The speed of the car should be sluggish and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork needs to be as deep as feasible under the load, and it needs to be noted that the fork pointer ought to not touch various other goods or objects. The tons needs to be supported with marginal back tilt of the gantry to ensure that the tons does not glide in reverse. The mast can be slanted onward slightly when the lots is lowered to allow for very easy positioning of the tons and extraction of the forks. .
6. It is restricted to fork products at broadband and hit difficult objects with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to loaf the fork, so as to avoid the collapse of the goods and hurt individuals. .
8. Overwhelming is banned, and it is banned to make use of forks Stand-on Electric Pallet Stacker to lift personnel to participate in high-altitude procedures to stay clear of high-altitude dropping mishaps. .
9. It is not enabled to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to select, transform pallet discharge.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you must dump the goods or reduced the fork structure.
2. Draw Stand-on Electric Pallet Stacker the hand brake deal with to dead or dispirit the parking brake switch.
3. The engine is turned off and the power is removed. (Except for special scenarios, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 minute).
4. Remove the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance needs to be inspected, and gas, lubricating oil and air conditioning water must be included.
2. Examine the security efficiency of beginning, running and braking.
3. Inspect whether the lights and horn signals are full and efficient.
4. Throughout the procedure of the forklift, check whether the stress and temperature are normal.
5. After the forklift is running, the exterior leak must additionally be checked and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the cars and truck;.
2. When you run into someone in front of you during driving, you ought to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not go beyond 5 km/h;.
4. When driving, the nadir of the freight must be 0.3 m ~ 0.4 m in the air;.
5. The transforming should not be too sharp to avoid the tendency of " cost-free switching";.
6. Adding and down the incline should be sluggish and consistent, and no switching on the slope is permitted.
7. Do not drive throughout the gradient. When the gradient is greater than 10%, the automobile ought to be driven in reverse when going downhill;.
8. When the forklift employees bring the goods and progress, if they run into huge or heavy items and go to the vehicle driver's line of sight, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the operation.
1. Single fork operation is not allowed.
2. It is not allowed to raise the goods for long distance driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not enabled to utilize inertia pressure to pick up the goods.
6. It is not enabled to make use of braking force to exile round or easy-to-roll things.
7. It is not allowed to bring people to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is elevated.
8. Do not drive side to side on inclines
.
Auto parking is not permitted under the list below problems.
1. Contours, narrow roads, railway crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the contrary side of the section with the very same length as the obstacle must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844